Not every small fitting on a valve is a grease point. Some feed the seats, some feed the stem seal, and others only vent or drain the body. The job depends on the position on the valve and the maker's design, not on looks. Check the valve tag and manual, and send us photographs before anything is connected.
How to identify the injection fittings on a valve
Seat, stem, vent and drain fittings can look alike, but each one has a different job.
1. Why a small fitting is not always a grease point
Many people see a small fitting on a valve and call it a grease nipple. That habit can cause real harm.
Some fittings feed sealant to the seats. Some feed the stem seal. Others only vent or drain the body cavity. Putting the wrong material into the wrong point can damage the valve.
The shape of a fitting does not tell you its job. Its position on the valve and the maker's design tell you.
Also, not every valve has injection fittings, and some makers fit none. Treatment in service needs fittings in good condition, a valve and duty that suit injection, and a site permit that allows the work. If any one is missing, the answer may be a proper assessment instead.
2. The families of fitting you may meet
Most fittings on an industrial valve belong to one of a few families. Position is the best first clue.
- Seat sealant fittings sit on the body where they can reach the seat area. They serve a passing seat.
- Stem sealant fittings sit close to the stem. They serve the stem seal when it leaks.
- Body vent and drain fittings sit on the body to relieve or drain the cavity. They are not feed points for sealant.
- Plug valve fittings may be a tall giant button head or a lube screw. These feed the plug sealing surfaces.
Gate and ball valves tend to carry short, stubby fittings. Plug valves often carry taller ones. This is a tendency, not a rule.
3. What button head and giant button head mean
The name comes from the shape. A button head fitting has a rounded, domed head like a button. A giant button head is a larger head of the same general idea.
The name describes the head, not the job. Two fittings with the same head can serve the seat, the stem or a vent. Two different heads can serve the same purpose.
Some fittings carry a cap with small vent holes. We cannot say from a photograph alone whether this differs from a plain button head. Treat it as unidentified until the maker's drawing says otherwise.
Head types, ratings and checks are covered in buttonhead injection fittings: identification, ratings and checks. Matching a connection to an unfamiliar head is a specialist task.
4. Why looks alone can mislead
The wrong fitting can be greased for years if nobody checks the maker's manual. Looks alone may give no warning.
Heavy paint can also hide a fitting that is not fully seated. A fitting that appears sound may not be. It may also be a replacement from another source. See non-standard valve fittings and why they appear.
So, do ball valves need routine greasing? Not by default. Some fittings are meant for emergency sealing or the stem seal, not for regular greasing. Any routine should come from the maker's manual and an assessment of the valve.
If a fitting is damaged, loose or leaking, stop. Do not connect anything to it.
5. What to photograph and send
A good set of photographs lets an engineer name each fitting before anyone touches it. The valve tag and maker's manual are the route to the exact type.
- The whole valve, from a distance, with the pipeline direction visible.
- Each fitting close up, from the side and from above, with its position on the body clear.
- The valve tag, so we can read the maker, type and reference.
- Any paint build-up, damage, caps or marks on a fitting.
- The service and the symptom, such as a passing seat or a leaking stem.
Our guide on what to tell us before an equipment enquiry adds detail. For many valves on one site, a valve survey records every fitting. The wider picture is in the injection equipment buying guide.
Identifying valve fittings questions, answered directly
Is the fitting on the valve stem really a grease point?
Not always. A fitting near the stem may feed the stem seal with sealant, and it is not a general grease point. Check the maker's manual and send photographs before putting anything into it.
What is the difference between a button head and a giant button head?
Both are named for their domed, button-like head. The giant button head is the larger of the two and is often seen on plug valves. The name describes the head, not the job it does.
Do ball valves need routine greasing through their fittings?
Not by default. Some fittings are for emergency sealing or the stem seal only. Any routine should follow the maker's manual and an assessment, and a specialist should set it.
How can I tell a body vent or drain fitting from a sealant fitting?
Position is the best clue, but looks can mislead. Vent and drain fittings relieve or drain the body cavity and do not feed sealant. Send photographs and the valve tag so an engineer can confirm.
Send the photographs. An engineer replies within 24 hours.
Include close photographs of each fitting, the whole valve, the valve tag, and the symptom you see, by WhatsApp or the contact form.