Mon-Fri 9am-6pm IST
Field team reviewing an installed valve before controlled maintenance work
Knowledge ยท Working with us

Valve care for pipeline project and commissioning contractors

What a project contractor should plan, settle in writing and send us before valves meet test water.

The short answer

Whether a valve stays in the line during testing and flushing, how it is positioned and whether it may serve as a test boundary are decided by the valve maker's instructions and the project test procedure. Have both in writing before the test. Keep debris and standing water out of the valve.

1. Should valves stay in the line during testing?

There is no single answer. Some valves are damaged because nobody asked the maker first, and that may affect the warranty position, which is a contract matter.

Test water and flushing flow carry weld spatter, scale and grit. Hard particles gouge ball and seat surfaces, so it is better to keep debris out than to clear it afterwards.

A line test proves the pipework and its joints. It does not prove valve sealing, and a valve is not automatically a good test end point. Whether a valve stays in the line, how it is positioned and whether it may serve as a test boundary are decided by the valve maker's instructions and the project test procedure. Have both in writing before the test.

2. Control valves, motor-operated valves and test ends

Control valves are often replaced by a temporary spool during the line test and fitted later. Whether that suits your line is a project decision. Ask the maker, and record the answer.

Motor-operated valves add actuator and electrical parts. The body may tolerate the test while the actuator or its seals do not. Ask the maker what the actuator and its seals may see, and record the answer. The maker's instructions and the project test procedure decide.

3. Order of installation and what test water leaves behind

Many contractors ask whether valves go in before or after the line test. A welded-in valve adds welds that the test then has to cover. Fitting later adds a joint to make and check afterwards. Both routes are used, so this is a project decision.

Test water is the second concern. Water left standing can saturate packing and pit stems, and wet pipe can pit and fail in service. Lubricant applied at the factory or for the test may not stay in the valve, so the owner may later meet packing leaks that adjustment cannot cure.

Plan these points before the work begins:

  1. Which valves are in the line, and which are replaced by spools.
  2. What the maker says about the test medium for each type.
  3. How long water may stay in the line after the test.
  4. Who records the valve condition before and after.

4. When a valve or a joint leaks in the test

A new valve may hold some pressure and then bleed back when it is used as the test end. That indicates a leak, and common causes include seat leakage, a trapped cavity or a settling seal. Other causes are possible. A seat-leak test under agreed conditions is the confirming step.

A valve that passed its shop test can still leak at site, as a valve passing after hydrotest shows. The maker's rating, the warranty terms and the party running the test all matter. Who carries the risk is a contract matter, and we give no verdict on it. Getting the maker's position in writing before the test is what protects the contractor.

An inspector who wants to reject a test over packing or body joint leakage is raising a fair question. Decide beforehand how such leaks are classed. For seat leakage that blocks isolation, see double block and bleed will not hold.

5. Valves waiting in a warehouse

A stalled project leaves valves in storage for a long time. Wetting and long waits can leave them leaking or pitted by the day they reach the line.

Storage care starts with the maker's instruction, and our guide to stored valve preservation covers the planning view. Ask for it in writing at purchase, and record each valve's condition when received.

If a delay is likely, tell the owner early. A valve that has waited a long time is better checked before installation than discovered passing after the line is live. Our valve surveys are one way to record condition, and where treatment suits the valve, we can advise on it. In-service treatment is not possible for every valve, and some should be repaired or replaced instead.

6. What to settle in writing and what to send us

Settle these points with the valve maker, the owner and the test authority before test water moves:

  1. Which valves stay in the line for testing and flushing, and why.
  2. The maker's written position on test medium, test boundaries and warranty.
  3. Which valves are replaced by temporary spools or strainers.
  4. How a leaking packing, body joint or seat will be recorded and judged.
  5. Storage conditions for valves not yet installed.

If a valve is already damaged, passing or seized, the next step is a proper assessment. We cover the handover side in leaving your team able to maintain what we treated. Our pillar guide on choosing an online valve maintenance provider explains how to judge a specialist. Our list of valve data to send in a first enquiry speeds the answer.

Common questions

Valves during line testing questions, answered directly

Can valves stay in the line during a pipeline test and flush?

Sometimes, but the valve maker's instructions and the project test procedure decide. Ask the maker in writing before testing with a valve in line, because a silent test may affect the warranty position, which is a contract matter.

Should control valves be replaced by a spool for the line test?

A temporary spool is common industry practice for control valves, with the valve fitted afterwards, sometimes with a temporary strainer. It is still a project decision, so confirm it with the maker and record it.

Why does a new valve hold pressure and then bleed back?

It indicates leakage across the seat or a trapped cavity, but pressure behaviour alone does not identify the cause. A pressure-decay or witnessed seat-leak test under agreed conditions is the confirming step.

What care do valves need when the project stalls?

Wetting, wet packing and long waits can leave stored valves leaking or pitted. Follow the maker's storage instruction, record condition on receipt, and have valves checked before installation after a long delay.

Valves delayed or damaged on site?

Send the valve details. An engineer replies within 24 hours.

Include valve type, size, maker, where it sits in the line, what happened during testing or storage, and photos of any damage.