Mon-Fri 9am-6pm IST
Technician operating a hydraulic sealant injection pump on a pipeline valve
Knowledge ยท Injection equipment

API 6D and sealant injection fittings: what the standard covers

A standard's name on a valve does not tell you whether it has injection fittings, or which ones.

The short answer

API 6D is a standard for the manufacture and acceptance of pipeline valves. Its name on a nameplate does not tell you which injection fittings a valve has. The valve data sheet, the purchase specification and the maker's manual do, and the order papers record the edition the valve was bought to.

1. What the standard is, and what it is not

API 6D is a standard for the manufacture and acceptance of pipeline valves. That is the level at which we describe it here.

The name on a nameplate or in a quotation tells you the valve was made and accepted under that standard. It does not tell you which fittings the valve carries, or whether it carries any.

The standard is not where this is answered for your valve. The data sheet, the purchase specification and the maker's documents are. Valves built with injection points are designed to be maintained in service, so find out which kind you hold.

2. Where the answer for your valve sits

Whether a valve has injection points depends on the maker's design, on what the buyer asked for, and on the service.

These documents hold the answer for a given valve:

  1. The valve data sheet, which lists the features the maker supplied.
  2. The purchase specification, which records what the buyer asked for.
  3. The maker's manual and drawings, which show the fittings and their limits.
  4. The order papers, which show the edition the valve was bought to.

If one of these is missing, the valve itself is the next place to look. Check the tag plate and look at the body for fittings.

3. When injection fittings are actually needed

Some valve designs are made to be treated in service. Others are not. Whether a trunnion valve with piston-type seats benefits from fittings is a design question for the maker's documents, not for a standard's name.

Fittings can also serve different jobs. Sealant fittings, body cavity relief and pressure monitoring are separate matters, and each depends on the design.

Before any treatment is considered, three gates apply. The fittings must be in good condition. The valve design and service must suit injection. Site rules and the permit-to-work must allow the job. To see how sealant reaches a seat, read where sealant goes in a ball valve.

4. Pressure limits, fittings and sealant choice

People often ask who sets the injection pressure, and what the fitting is and which thread it has. Read the maker's drawings for the fitting and thread.

The injection limit for your valve comes from the maker's documents and the ratings of the equipment and fitting. Trained people keep within the lowest of them and watch the pressure response throughout.

Stop and ask for advice if the pressure response is not as expected, or if a fitting is damaged or leaks.

Whether the injection lines on a valve were tested, and how, is a question for the maker's test records. Ask for them by name.

Sealant choice sits with the service conditions and the people who make and apply the compound. If the fitting looks unusual, read what to do with a non-standard fitting.

5. Why the edition matters, and what to send us

Note the edition on the order papers and the purchase specification, and send it to us. We can help you read these documents. A valve condition survey can also record what fittings a valve really carries. For wider context, see the injection equipment buying guide.

To get a useful answer, send us:

  1. The valve data sheet and the tag plate details.
  2. The pages of the purchase specification that cover fittings.
  3. The maker's manual or drawings, if you have them.
  4. Photographs of the valve body, stem and any fittings.
  5. The service fluid and what problem you have seen.
Common questions

API 6D and fittings questions, answered directly

Does API 6D say which valves must have injection fittings?

The standard is not where this is answered for your valve. The data sheet, the purchase specification and the maker's manual are. Send us those documents and we will help you read them.

Where do I find which API 6D edition my valve was bought to?

The edition is recorded on the order papers and the purchase specification. Send both to us, with the maker's documents, and we will help you read them.

Who decides how hard to inject into a valve?

The maker's documents and the ratings of the equipment and fittings set the limit. A trained specialist should work within those limits and watch the pressure response.

Are the injection lines on a pipeline valve tested?

We cannot say from the standard's name alone. The maker's test records and the purchase specification show what was tested on your valve. Ask the maker for them, or send them to us and we will help read them.

Unsure what your valve has?

Send the valve documents. An engineer replies within 24 hours.

Include the data sheet, purchase specification pages, maker's manual, tag plate photograph, photographs of any fittings, and a short note of the service and problem.